Brief introduction of the HMI(Human Machine Interface)of the vertical form fill seal machine
The HMI system of the vffs machine made in China is consist of the following screens:
1) Language/Contact us----There are 2 or more optional language choices, ENGLISH ,Chinese, or even More. And also the supplier’s contact information.
2）Homepage----Main menu. The home page shows the all six menus, or seven menus: AUTOMATIC, MANUAL, FUNCTION, PARAMETER, ALARM and CONTACT US ( Monitor if total seven meus).
3) Automatic----Automatic operate interface, also main operate screen.
There are Start/stop switches for FILL BAG,TEST and FILM PULL, Hot order button for MAKE ONE BAG , Adjust button for ERROR CLRRECT, and Display of BAG LENGTH, PACKING SPEED, & QUOTA,FILLING COUNTER along with RESET. In the bottom of the page is menu changing buttons. When press any of them, the machine turn to the related menu.
4）Manual---- Main menu.
There are the order buttons of INCH PULL FILM, MAKE ONE BAG, ONCE FILL, HORI.SEAL OPEN, VERT.SEAL OPEN, CUTTER UNTREAD, FILM PULL OPEN, FILL PULL STOP , and FEEDER ON .
5）Function---- A group of Start/stop switches for related functions.
There are Start/stop switches of EYE MARK, FILL OPEN/OFF, FILL PLAN, CUTTER OFF/ON, EYE MARK ON/OFF and FEEDER ON/OFF.
5）Parameter---- three screens of general parameter setting.
There are a series of TIME and DELAY settings such as VERL.SEAL TIME and FILM PULL DELAY .
6）Alarm---- There are alarm switches ( ON/OFF) of HORI. VERT. TEMPERATURE NORMAL, HORI. SEAL SERVO SYSTEM NORMAL, DELIVER SERVO SYSTEM NORMAL, FILM PULL SYSTEM NORMAL, SAFETY DOOR CLOSE and the sign of EMERGENCY SWITCH REPLACEMENT STATE.
7) Monitor--- it shows connecting & running states of output and input of PLC.
After switching on the machine, you’ll see the screen shines and the Language Interface will appear.
Press the ENGLISH, and you’ll go into the homepage as following :
Automatic menu: Touch AUTOMATIC and the screen will show as below:
There are Start/stop switches for FILL BAG,TEST and FILM PULL, Hot order button for MAKE ONE BAG , Adjust button for ERROR CLRRECT, and Display of BAG LENGTH, PACKING SPEED, & QUOTA,FILLING COUNTER along with RESET. Press the FILL BAG or the green START/STOP button under the powder switch he machine will run continuously as the set parameters after done all the parameters setting .
1) BAG LENGTH----It shows the bag length under current program number. However the bag length cannot be changed over here.
2) FILL BAG----It is used with dosing head. When packaging machine is connecting with dosing head, press START, PLC will keep outputting signal of filling, and drive other auger dosing head to work together. PLC also will send signal at preset speed, and ask for filling. With this function the machine will fill product continuously by adopting the principle of sending signal to each other. Press STOP or the green START/STOP button under the powder switch to stop it. Also same by pressing Emergency switch.
3) TEST----It is only used for testing. Press Start, packaging machine will make one empty bag at preset bag length and speed and other parameters. Press Stop to stop it.
4) FILM PULL---- It is used for making forming tube to clamp the double pulling belt to make it pull film downward. Press OPEN, pulling belt will move closer to forming tube to make it pull film. Press CLOSE, pulling belt will depart from forming tube and stop working. Press emergency switch, pulling belt system will depart from forming tube. Reset emergency switch, pulling belt system will move closer to the both sides of forming tube.
5) MAKE ONE BAG----It is used for making one empty bag. Press MAKE ONE BAG, machine will make an empty bag at preset bag length and other parameters. After it stops, you can press the button again to make one more bag if necessary.
6) ERROR CORRECT----It is used for correcting film pulling( The vertical sealing shows the performance of film pulling). If the vertical sealing is not matched well, press left or right arrow to adjust it.
7) PACKING SPEED----It is only for showing the current packing speed of packaging machine or measuring system. It cannot be changed over here, please enter the parameter setting (1/3) page to change it.
8) QUOTA----It shows the SET output of packed bags. The machine is to stop running when the actual output has been up to the set QUOTA.
9) FILL COUNTER/BAG COUNTER---- It shows the total output of packed bags from press FILL BAG to stop it. Press RESET to reset the output value.
In the bottom of the page is menu changing buttons. When press any of them, the machine turn to the related menu.
Function menu: Touch FUNCTION，the function menu will show as below.
There are Start/stop switches of EYE MARK, FILL OPEN/OFF, CUTTER OFF/ON, FEEDER OFF/ON, BLUNT GAS ON/OFF, change-over switches of FILL PLAN, EYE MARK ON/OFF , adjust button couple of EYE MARK MOTOR, and CODE DELAY time setting blank.
1) EYE MARK----It is the general switch of the photocell, and used for tracking photocell on the film to identify bag length (specific bag length is related to the design of the using film). Press OFF, it turns to ON condition, the machine will run under the order of tracking bag length. (Please reference to PARAMETER (1/3) to know how to set bag length. Press ON, it turns to OFF condition, the machine will run at preset bag length under the order of fixed bag length.
2) FILL OPEN/OFF---- It is the switch of the 14-heads weigher filling system. Press OFF, it turns to ON condition, the weigher will work. Press ON, it turns to OFF condition.
3) FILL PLAN----It is program changing switch of “Plan 1/Plan 2” pull-seal-fill- program/way. Plan 1= fill while pulling film, and then seal & cut; Plan 2= seal & cut, fill, and then pull film.
4) CUTTER ON/OFF ----It is program switch of the cutter. Press OFF, it turns to ON condition, the cutter will work automatically. Press ON, it turns to OFF condition.
5) EYE MARK UP/Down----It is used for locating the eye mark to be cut off. If any deviation was found in the pattern of the finished bag, please press up or down arrow to adjust the location. Notice: When this function is On, press the key can adjust the location. When this function is Off, press the key is invalid, it means that the machine is under the order of fixed bag length.
6) EYE MARK ON/OFF----It is the changing switch of the photocell working model. EYE MARK ON means that the photocell is turning on when the photocell has caught the eye marks, and the photocell is turning on while the photocell is tracking between two eye marks. EYE MARK OFF does that the photocell is turning off when the photocell has caught the eye marks.
7) FEEDER ON/OFF---- It is the switch of the Z bucket elevator.
8) BLUNT GAS ON/OFF--- It is the switch of the gas charging value.
For the full introductions of the China vertical FFS machine’s HMI , or more background information of the vertical form fill seal packing machine, freely contact Mr. Ray LEE by email or WeChat(WhatsAPP).
WeChat/WhatsAPP: +86 1860204723
Previous: No Information
- Guangzhou Herbal Tea Packaging Powd...
- Guangzhou Quantitative Packaging Au...
- Guangzhou Screw Packing High Speed ...
- Corn Automatic Packaging Machine Fa...
- Number Of Guangzhou Automatic Packa...
- Which Is The Best Particle Packing ...
- Screw Packaging Machine Sales Proce...
- Times Technology Of Guangzhou Autom...
- What Is The New R & D Technology Of...
- How To Quote Price Of Guangzhou Gra...
- Multihead Weigher Filler Packing Ma...
- New Stick Packaging Machine
- New Sachet Packaging Machine
- Mini Pre-made Pouch Pick Open Fill ...